Understanding Plumbing Basics When Installing a Bathtub
Understanding Plumbing Basics When Installing a Bathtub
Blog Article
Are you currently trying to locate information on Installing A Bathtub?
Mounting a bathtub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably tough job. If the old bathtub is readily easily accessible, the task can move easily; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the task as well as fit attempting it. Instead of working with a specialist to take over a halfway-completed task, it is better to consider utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This post will certainly aid you mount a new bath tub in your shower room if you have actually currently acquired a new tub and also do not require to change the setup of your previous water pipes.
Your tools and material list should make up the following:
Getting ready for the Setup
Firstly, the supporting structure supplied with the bath should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last position.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Before going on to fit the new taps, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Making use of both wood boards under its feet, position the bath tub in the called for position. The wooden boards are helpful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub until the spirit level checks out level.
To mount taps, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the supply of water and also examine all joints as well as new pipework for leakages as well as tighten them if needed. Fill the bath tub as well as also examine the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, fix the bath paneling as defined in the producer's instruction manual. Tiling as well as securing around the bath tub ought to wait until the tub has actually been utilized at least once as this will resolve it right into its final position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in place in between the tap as well as the sink. Protect the faucet in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The former type must be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, leading to issues with dampness as well as possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and also cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can fracture rather early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the market. It is recommended to fit the floor tiles utilizing waterproof or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our article on How to Install a Bathtub Yourself. Thanks a ton for taking a few minutes to read through our article post. Enjoyed our article? Please share it. Let other people check it out. We enjoy reading our article about How to Install a Bathtub Yourself.
Expertise available here. Report this page